Welcome to
Search

Main Menu
· Home
· Downloads

Knowledge Base
·Main
·Procedures & Solutions
·Errors and Troubleshooting
·Frequently Asked Questions

  



[ Downloads Main | Add Download | New | Popular | Top Rated ]

Category: Main/_Archive/Digital Wrench 4.2 Updates Archive


Sort Downloads by: Title (A\D) Date (A\D) Rating (A\D) Popularity (A\D)
Resources currently sorted by: Popularity (Least to Most Hits)


  Digital Wrench Version 4.2 Update 11/03/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 11/03/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Model Year 2021 International 570 ATV Models
-Revised Calibrations for Indian Motorcycles
-Addition of Performance Calibrations for 20201 Indian Motorcycles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 11/03/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_110320 Filesize: 87.56 MB
Added on: 03-Nov-2020 Downloads: 608
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 04/14/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 04/14/21 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Diagrams for RANGER PWM Cooling Fans
-Addition of Taylor-Dunn Vehicles
-Addition of ABS Diagnostic Data for Scout Sixty Motorcycles
-Revised EPS Calibration for RANGER XP 1000 vehicles

IMPORTANT: This update will also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 04/14/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_041421 Filesize: 139.71 MB
Added on: 14-Apr-2021 Downloads: 1114
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 04/22/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 04/22/21 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Stage 2 and Stage 3 Calibrations for Indian Chief/Bobber/Super Motorcycles.

IMPORTANT: This update will also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 04/22/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_042221 Filesize: 143.18 MB
Added on: 22-Apr-2021 Downloads: 1147
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 01/20/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 01/20/21 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Paddle Shift Accessory for 2021 Slingshot ATM
-Revised Calibrations for FTR Motorcycles
-Addition of 2021 ATV Twin Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 01/20/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_012021 Filesize: 112.62 MB
Added on: 20-Jan-2021 Downloads: 1199
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 01/26/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 01/26/21 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2021 RZR S 1000 International Models.

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 01/26/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_012621 Filesize: 114.07 MB
Added on: 26-Jan-2021 Downloads: 1504
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 11/06/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 11/06/20 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations for Indian Motorcycles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 11/06/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_110620 Filesize: 87.55 MB
Added on: 04-Nov-2020 Downloads: 1776
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 03/12/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 03/12/21 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2022 Indian Chief/Bobber/Super Motorcycles
-Addition of 2022 Indian FTR Motorcycles
-Addition of Performance Calibrations for Canada Slingshot Models
-Addition of 2021 Rzr Brazil Models
-Addition of 2021 General Models

IMPORTANT: This update will also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 03/12/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_031221 Filesize: 134.30 MB
Added on: 12-Mar-2021 Downloads: 1814
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 12/18/2020 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 12/18/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Hill Hold Feature for 2020 Slingshot
-Addition of Paddle Shift Feature for 2020 Slingshot

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 12/18/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_121820 Filesize: 109.36 MB
Added on: 18-Dec-2020 Downloads: 1835
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 12/09/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 12/09/20 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations for 2019-2021 650&850 Snowmobile Voltage Regulators
-Addition of 2021 Slingshot Models
-Additional Vehicle Conversions for 2021 Scout Sixty Models
-Revised Calibrations for 2011 111 CI Chief Vintage Models


IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 12/09/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_120920 Filesize: 108.87 MB
Added on: 10-Dec-2020 Downloads: 1869
HomePage | Rate Resource | Details

  Digital Wrench Version 4.2 Update 02/24/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 02/04/21 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Vehicle Identification Parameters for 2021 Ranger Diesel International Vehicles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 02/24/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_022421 Filesize: 124.33 MB
Added on: 25-Feb-2021 Downloads: 1954
HomePage | Rate Resource | Details



Select Page: 1 2 3   [ Next Page >> ]
  
Who's Online
There are currently, 16 guest(s) and 0 member(s) that are online.

You are Anonymous user. You can register for free by clicking here

All logos and trademarks in this site are property of their respective owner. The comments are property of their posters, all the rest � 2003-2004 by Diagnostic Systems Associates, Inc.
Web site engine's code is Copyright © 2003 by PHP-Nuke. All Rights Reserved. PHP-Nuke is Free Software released under the GNU/GPL license.
Page Generation: 0.221 Seconds