Welcome to
Search

Main Menu
· Home
· Downloads

Knowledge Base
·Main
·Procedures & Solutions
·Errors and Troubleshooting
·Frequently Asked Questions

  



[ Downloads Main | Add Download | New | Popular | Top Rated ]

Category: Main/_Archive/Digital Wrench 4.1 Updates Archive


Sort Downloads by: Title (A\D) Date (A\D) Rating (A\D) Popularity (A\D)
Resources currently sorted by: Title (Z to A)


  Digital Wrench Version 4.1 Update 04/13/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 04/13/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Performance Calibration for 2020 Slingshot
-Addition of 2020 RZR 900 Ride Command Vehicle
-Revised EPS Centering Procedure for Dynamix
-Addition of 2017 Ranger 800 6x6 Vehicle

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 04/13/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_041320 Filesize: 114.78 MB
Added on: 14-Apr-2020 Downloads: 1591
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 04/03/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 04/03/20 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations for 2019-2020 Ranger 1000 Models
-Addition of 2021 Sportsman & Scrambler 1000 S Models
-Addition of 2021 Outlaw 70

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 04/03/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_040320 Filesize: 119 bytes
Added on: 03-Apr-2020 Downloads: 1662
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 03/26/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 03/26/20 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations for 2019-2020 Ranger 1000 Models
-Addition of 2020 Sportsman 570 California Models
-Updated Calibration for 2020 Indian Challenger International Motorcycles
-Revised Vehicle Update Procedure for 2020 Indian Motorcycles
-Additional Calibration for 2019 RANGER HD Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 03/26/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_032620 Filesize: 110.02 MB
Added on: 27-Mar-2020 Downloads: 2511
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 03/13/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 03/13/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 Slingshot AMT Models
-Revised Vehicle Update Procedure for Indian FTR Motorcycles
-Revised Vehicle Update Procedure for Indian Motorcycles
-Addition of 2020 Ranger Diesel Models
-Additional 2020 Sportsman Models
-Revised ECU Calibration for 850 Axys Snowmobiles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 03/13/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_031320 Filesize: 108 bytes
Added on: 13-Mar-2020 Downloads: 1927
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 02/26/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 02/26/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 Indian FTR Models
-Revised Calibration for 2014-2017 Indian Vehicle Control Module
-Revised Calibrations for 2020 Indian Challenger Models
-Addition of 2020 GEM Models
-Additional 2020 Indian Scout and Scout Sixty Models
-Additional Calibration for 2019 Ranger HD Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 02/26/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_022620 Filesize: 101.69 MB
Added on: 26-Feb-2020 Downloads: 1957
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 02/05/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 02/05/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 RZR International Models
-Revisised Calibration for 2019 Indian FTR North American Modelss

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 02/05/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_020520 Filesize: 99.26 MB
Added on: 06-Feb-2020 Downloads: 2274
HomePage | Rate Resource | Details

  Digital Wrench Version 4.1 Update 01/22/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 01/22/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 RANGER International Models
-Addition of 2020 General International Models
-Addition of Stage Calibrations for 2020 Indian Midsize Models
-Addition of 2020 ATV Single International Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 01/22/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_012220 Filesize: 96.51 MB
Added on: 23-Jan-2020 Downloads: 2398
HomePage | Rate Resource | Details



Select Page:   [ << Previous Page ] 1 2 
  
Who's Online
There are currently, 17 guest(s) and 0 member(s) that are online.

You are Anonymous user. You can register for free by clicking here

All logos and trademarks in this site are property of their respective owner. The comments are property of their posters, all the rest � 2003-2004 by Diagnostic Systems Associates, Inc.
Web site engine's code is Copyright © 2003 by PHP-Nuke. All Rights Reserved. PHP-Nuke is Free Software released under the GNU/GPL license.
Page Generation: 0.224 Seconds