Welcome to
Search

Main Menu
· Home
· Downloads

Knowledge Base
·Main
·Procedures & Solutions
·Errors and Troubleshooting
·Frequently Asked Questions

  



[ Downloads Main | Add Download | New | Popular | Top Rated ]

Most Popular - Top 25
Show Top: [ 10 - 25 - 50 | 1% - 5% - 10% ]


  DSA USB-Serial Adapter Drivers 2000/XP/Vista  Popular
Description: Drivers for the DSA USB-Serial Adapter.

These drivers are for use with the USB-Serial Adapter from DSA.

Supports Windows 2000, XP and Vista.

Windows 95, 98 and ME are NOT supported with this driver.

Download and run the installer and then connect the USB-Serial Adapter.

Always right-click on the installer and select "Run as Administrator" when installing on Windows Vista.

IMPORTANT: ALWAYS UNINSTALL THE OLD DRIVERS FOR THIS ADAPTER BEFORE INSTALLING NEW ONES.
Version: 2.06.00 Filesize: 2.24 MB
Added on: 20-Jan-2006 Downloads: 16734
HomePage | Rate Resource | Details
Category: USB Adapter Drivers/USB Adapter Drivers

  Digital Wrench Version 4.3 Update 02/08/2022  Popular
Description: This update consists of all changes to Digital Wrench Version 4.3 since the original version was released in August 2021.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.3 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.3 INSTALLER. Communication with the RZR Pro R, Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 02/08/22 Includes the following changes & additions from the original program release and Previous Updates:

- Addition of 2021 RZR 200 Models
- Addition of 2022 Ranger EV Models
- Addition of 2022 China Indian Models
- Revised Calibrations for 2020-2021 Indian Challenger Motorcycles
- Additional 2021 Indian Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.3 02/08/2022".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 43_020821 Filesize: 65.32 MB
Added on: 08-Feb-2022 Downloads: 16558
HomePage | Rate Resource | Details
Category: Digital Wrench Version 4.3 Updates/ Digital Wrench Version 4.3 Updates

  Digital Wrench Version 3.0 User Guide  Popular
Description: The Digital Wrench Version 3.0 User Guide in Adobe PDF Format
Version: 3.0 Filesize: 3.89 MB
Added on: 10-Jul-2007 Downloads: 10806
HomePage | Rate Resource | Details
Category: Documentation/Documentation

  Digital Wrench Version 4.3 Update 09/29/2021  Popular
Description: This update consists of all changes to Digital Wrench Version 4.3 since the original version was released in August 2021.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.3 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.3 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 09/29/21 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2022 600 and 800 Snow Models.
-Revised EPS Calibration for certain 2021 ATV Models.
-Revised Calibrations for 2019-2021 Indian China Models.
-Additional 2020 FTR 1200 Models.
-Additional 2021 Ranger 150 Models.
-Additional 2021 RZR Models.
-Revised Speedometer Calibration for 2021 Indian Models.

IMPORTANT: This update mayalso perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.3 09/29/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 43_092921 Filesize: 51.38 MB
Added on: 29-Sep-2021 Downloads: 6779
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.3 Updates Archive

  Digital Wrench Version 3.9 Update 08/31/17  Popular
Description:

This update consists of all changes to Digital Wrench Version 3.8 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 08/31/17 Includes the following changes & additions from the original program release and Previous Updates:

-Fix to the RZR Turbo Dynamix Steering Angle Centering Procedure.

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 08/31/17".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_083117 Filesize: 19.02 MB
Added on: 05-Sep-2017 Downloads: 5921
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 3.9 Update 07/22/18  Popular
Description:

This update consists of all changes to Digital Wrench Version 3.9 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 07/22/18 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2019 RANGER XP CREW Models.
-Addition of 2019 RANGER XP and Highlifter Models
-Revised Instrument Cluster Calibration for 2018 RANGER XP 1000
-Revised ECU Calibration for 2018 SP 570 6x6
-Revised ECU Calibrations for 2015-2018 Slingshot
-Revised Fan Control Test for 2017-2019 RZR Turbo Vehicles

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 07/22/18".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_072218 Filesize: 109.59 MB
Added on: 22-Jul-2018 Downloads: 5644
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 4.1 Update 06/15/2020  Popular
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 06/15/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Model Year 2020 Ranger / RZR 150 Vehicles
-Addition of Model Year 2020 ACE 170 Vehicles
-Addition of Model Year 2020 Sportsman 110 Vehicles
-Addition of Model Year 2019 E28 RZR Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 06/15/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_061520 Filesize: 125.12 MB
Added on: 16-Jun-2020 Downloads: 5605
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.3 Update 12/27/2021  Popular
Description: This update consists of all changes to Digital Wrench Version 4.3 since the original version was released in August 2021.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.3 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.3 INSTALLER. Communication with the RZR Pro R, Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 12/27/21 Includes the following changes & additions from the original program release and Previous Updates:

- Adds Additional 2021 Indian Models
- Adds 600 Race Snowmobile
- Adds 2022 600 Cross Country Snowmobile
- Adds 2022 Youth Vehicles
- Adds Guided Diagnostics for 2020-2021 Slingshot

- Includes MultiLink Update File to convert MultiLink XP Modules to Direct USB Devices.

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.3 12/27/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 43_122721 Filesize: 56.21 MB
Added on: 26-Dec-2021 Downloads: 5557
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.3 Updates Archive

  Digital Wrench Version 4.0 Update 09/03/2019 
Description:

This update consists of all changes to Digital Wrench Version 4.0 since the original version was released in August 2018.

This is the final version 4.0 update

*************************

IMPORTANT:

DIGITAL WRENCH 4.1 HAS BEEEN RELEASED.
FOR MODEL YEAR 2020 VEHICLES PROCEED TO THE BASE INSTALLER OR SUBSCRIPTIONS LINK FOR THE NEW VERSION.

*************************

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.0 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on this vehicle

Update 09/03/19 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Vehicle Update Process for Indian Motorcycles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.0 09/03/2019".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 40_090319 Filesize: 96.53 MB
Added on: 03-Sep-2019 Downloads: 4936
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.0 Updates Archive

  DW Registry Cleanup Uility 
Description: This utility program can be used to clean up the Windows Registry when there are problems with the Windows Installer that prevent the Digital Wrench from being installed or re-installed. Refer to the knowledge base article called "How to run the DWRegCleanUp Utility" for more information.

This utility is not needed for Digital Wrench version 3.
Version: Filesize: 29.00 Kb
Added on: 03-Nov-2004 Downloads: 4909
HomePage | Rate Resource | Details
Category: Other Files/Other Files

  Digital Wrench Version 4.1 Update 05/07/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 05/07/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of revised VCM Calibration for Indian Motorcycles missing from the previous update
-Addition of 2020 Slingshot Manual Transmission Models
-Addition of 2020 International RZR Models
-Addition of 2020 Mid-Year RZR Turbo Models
-Addition of 2021 Ranger 570 International Models
-Revised Calibrations for 2019 RANGER and RZR XP 1000 Vehicles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 05/07/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_050720 Filesize: 123.98 MB
Added on: 07-May-2020 Downloads: 4552
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 3.9 Update 05/15/18 
Description:

This update consists of all changes to Digital Wrench Version 3.9 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 05/15/18 Includes the following changes & additions from the original program release and Previous Updates:

-Updated Calibration for 2018 RZR RS1.
-Additional 2018 Military Snow Models
-Additional 2018 RANGER Models
-Addition of 2019 RANGER XP Crew Models
-Updated Calibration for 2018 Indian (China Models)

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 05/15/18".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_051518 Filesize: 103.73 MB
Added on: 16-May-2018 Downloads: 4232
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 4.2 Update 07/29/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 07/06/21 Includes the following changes & additions from the original program release and Previous Updates:

-Revised VCM3 Calibration for Indian Challenger Motorcycles.
-Addition of Speedkey option for 2021 Ranger 1000 HD Vehicles.

IMPORTANT: This update mayalso perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 07/29/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_072921 Filesize: 0 bytes
Added on: 31-Jul-2021 Downloads: 4101
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.2 Updates Archive

  Digital Wrench Version 3.9 Update 01/16/18 
Description:

This update consists of all changes to Digital Wrench Version 3.9 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 01/16/18 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of RZR XP4 Turbo Dynamix Edition Vehicle
-Addition of Sportsman 110 ATV Vehicle
-Addition of RZR 170 Vehicle
-Addition of Sportsman 570 6x6 Tractor Vehicle
-Revised Instrument Cluster Calibrations for ATV models using the B1 (Square) display

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 01/16/18".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_011618 Filesize: 90.50 MB
Added on: 16-Jan-2018 Downloads: 3915
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 4.1 Update 09/26/2019 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on this vehicle

Update 09/26/19 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Stage Calibrations for 2020 Indian Motorcycles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 09/26/2019".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_092619 Filesize: 23.42 MB
Added on: 29-Sep-2019 Downloads: 3759
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.2 Update 11/16/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 11/16/20 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations 2018-2020 RANGER XP 1000 Models
-Addition of 2021 RZR Latin Models
-Revised Vehicle Update Procedure for 2020 Indian Challenger Models
-Revised VCM and ECU Calibrations for 2020 Indian Challenger Models
-Revised Calibrations for Indian Heavyweight Models
IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 11/16/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_111620 Filesize: 102.95 MB
Added on: 16-Nov-2020 Downloads: 3698
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.2 Updates Archive

  Digital Wrench Version 3.9 Update 03/30/18 
Description:

This update consists of all changes to Digital Wrench Version 3.9 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 03/30/18 Includes the following changes & additions from the original program release and Previous Updates:

-ECU Calibration for 2018 RZR 170.
-Updated Instrument Cluster Calibration for 2018 ACE Vehicles
-Revision to the ECU Update procedure for 2016 Ranger Diesel
-Revision to the SpeedKey Enablment procedure for GEM Vehicles

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 03/30/18".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_033018 Filesize: 102.66 MB
Added on: 03-Apr-2018 Downloads: 3621
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 4.1 Update 12/18/2019 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 12/18/19 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 RZR North American Models
-Addition of 2020 RZR International Models
-Addition of 2020 General Models
-Addition of 2020 ATV Single Models
-Addition of 2020 ATV Twin Models
-Revised Instrument Cluster Calibration for Ranger 100O HD Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 12/18/2019".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_121819 Filesize: 79.74 MB
Added on: 19-Dec-2019 Downloads: 3586
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.1 Update 11/20/2019 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on this vehicle

Update 11/20/19 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 RZR Models
-Revised Stage 3 Calibration for 2014-2017 Indian Motorcycles
-Revised dianostics for 2016-2019 GEM Vehicles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 11/20/2019".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_112019 Filesize: 42.95 MB
Added on: 20-Nov-2019 Downloads: 3526
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.1 Update 10/14/2019 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on this vehicle

Update 10/14/19 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 Ranger XP Vehicles
-Addition of 2020 450 and 570 ATV Models
-Addition of new FTR 1200 Models
-Addition of Revised Instrument Cluster Calibrations for certain Indian Motorcycles.

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 10/14/2019".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_101419 Filesize: 25.24 MB
Added on: 15-Oct-2019 Downloads: 3338
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.2 Update 05/25/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger, FTR and 2022 Chief Motorcycles is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 05/25/21 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Calibrations for 2021 PRO XD Vehicles.
-Revised Calibration for 2022 Indian Chief/Bobber/Super Vehicle Control Module
-Revisions to Challenger Vehicle Update Procedure
-Revised Trouble Code lists for RZR XP Turbo Vehicles

IMPORTANT: This update will also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 05/25/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_052521 Filesize: 143.90 MB
Added on: 26-May-2021 Downloads: 3194
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.2 Updates Archive

  Digital Wrench Version 4.1 Update 01/22/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 01/22/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of 2020 RANGER International Models
-Addition of 2020 General International Models
-Addition of Stage Calibrations for 2020 Indian Midsize Models
-Addition of 2020 ATV Single International Models

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 01/22/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_012220 Filesize: 96.51 MB
Added on: 23-Jan-2020 Downloads: 3163
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 4.1 Update 05/26/2020 
Description:

This update consists of all changes to Digital Wrench Version 4.1 since the original version was released in September 2019.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 7 (SP1), Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.1 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.0 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 05/26/20 Includes the following changes & additions from the original program release and Previous Updates:

-Addition of Transmission Service Procedures for 2020 AMT Slinshot vehicles.
-Addition of revised Instrument Cluster calibration for international RANGER and RZR Tractor models
-Addition of 2020 Late Release RZR Models
-Addition of Instrument Cluster Replacement Procedure for Indian FTR Motorcycles
-Addition of Guided Diagnostic Procedures for specific trouble codes on 2020 Indian Challenger
-Addition of SCM Actuator Test for Dynamix equipped vehicles
-Additional Accumulators and Histograms for certain vehicles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.1 05/26/2020".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 41_052620 Filesize: 124.01 MB
Added on: 27-May-2020 Downloads: 3105
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.1 Updates Archive

  Digital Wrench Version 3.9 Update 03/02/18 
Description:

This update consists of all changes to Digital Wrench Version 3.9 since the original version was released in August 2017.

IMPORTANT:

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 3.9 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 3.9 INSTALLER.

Update 03/02/18 Includes the following changes & additions from the original program release and Previous Updates:

-Updated Battery Controller Calibrations for GEM Vehicles.
-Addition of 2018 Ranger 150
-Addition of 2019 Axys 800 Early Build Snowmobiles

IMPORTANT: This update may also perform a firmware update on the SmartLink Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 3.9 03/02/18".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 39_030218 Filesize: 99.23 MB
Added on: 05-Mar-2018 Downloads: 3095
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench Version 3.9 Updates Archive

  Digital Wrench Version 4.2 Update 01/04/2021 
Description: This update consists of all changes to Digital Wrench Version 4.2 since the original version was released in August 2020.

IMPORTANT:

-Digital Wrench software is supported ONLY ON Windows 8 or Windows 10.
-Digital Wrench WILL NOT FUNCTION CORRECTLY ON Windows XP. or Windows 7.
-Digital Wrench WILL NOT INSTALL on Windows Versions older than Windows XP.

THIS UPDATE WILL NOT INSTALL ON OLDER VERSIONS OF DIGITAL WRENCH. YOU MUST ALREADY HAVE VERSION 4.2 INSTALLED ON YOUR PC BEFORE ATTEMPTING TO INSTALL THIS UPDATE.

FOLLOW THE APPROPRIATE LINKS ON THE DEALER EXTRANET OR CONTACT POLARIS TECHNICAL SUPPORT IF YOU NEED INFORMATION ON HOW TO OBTAIN THE DIGITAL WRENCH VERSION 4.2 INSTALLER. Communication with the Indian Challenger and FTR 1200 Motorcycle is only possible using the MultiLink XP Interface Module.
SmartLink Modules will not function on these vehicles.

Update 01/04/21 Includes the following changes & additions from the original program release and Previous Updates:

-Revised Update Procedure for 2020 Slingshot
-Revised Calibrations for MY 2021 RZR Vehicles
-Addition of 2021 Challenger International Vehicles

IMPORTANT: This update may also perform a firmware update on either the SmartLink or MultiLink XP Interface Module the first time it is connected. This update procedure must be allowed to complete before using the SmartLink or MultiLink XP.

NOTE: Reflashing a calibration should only be performed while working on a related issue, replacing an ECU or if there is an outstanding Service Bulletin requiring the ECU to be reflashed.

Click the link above, save the file to your hard disk and then double-click the icon to start the update process.

When the update is complete, the Version shown on the right side of the Digital Wrench Start-up Screen should read "Version 4.2 01/04/2021".

Note: Do not "run" or "open" the file from where they are. Select "save" and download them to your PC before running the install.


Version: 42_010421 Filesize: 112.05 MB
Added on: 05-Jan-2021 Downloads: 2976
HomePage | Rate Resource | Details
Category: _Archive/Digital Wrench 4.2 Updates Archive

  
Who's Online
There are currently, 19 guest(s) and 0 member(s) that are online.

You are Anonymous user. You can register for free by clicking here

All logos and trademarks in this site are property of their respective owner. The comments are property of their posters, all the rest � 2003-2004 by Diagnostic Systems Associates, Inc.
Web site engine's code is Copyright © 2003 by PHP-Nuke. All Rights Reserved. PHP-Nuke is Free Software released under the GNU/GPL license.
Page Generation: 0.354 Seconds